How to build a PVC pool towel rack

by Melissa

How to build a functional PVC pool towel rack.

A simple DIY that is perfect for your backyard pool needs. This rack will keep dripping towels and suits off the floor and out of the house.

This picture shows a rack made out of PVC material, white in color, showing pool towels, bathing suits, and other accessories hanging over the side to dry. PVC Pool Towel Rack


There are so many great things you can do with PVC pipe, from kids car washes to shoe organizers.

Just search PVC on Pinterest and you will find a boatload of ideas if you’re interested.

During the Summer we are usually outside in the pool every single day so washing towels or swimsuits daily just wasn’t going to work.

Of course, you can purchase one if you would like, but we didn’t really need one that big nor did I want to spend $200+.


There are all kinds of ways you can go about making a PVC pool towel rack from simple designs to large designs but we just wanted something simple that would hold our towels, plus a few swimsuits.

Want to make your own? Here is how…

Materials you will need:

(3) 10′ PVC Pipes

(We used 1 1/4″ piping. If you use a smaller/bigger size make sure you get the correct fittings as well)

(4) 1 1/4″ elbows (the feet)
(4) 1 1/4″ tees
(4) 1 1/4″ 90° elbow with slip


Here are some pictures if the fitting sizes are confusing.



This picture below is called a sideout elbow.

This would work in place of the tee and elbow with the slip if you can find one in the sizing you need. We couldn’t find any in the 1 1/4″ size.

 


Cuts you will need to make:

(4) 37″ pipe cuts (legs)
(2) 60″ pipe cuts (towel bars)
(4) 17.5″ pipe cuts (side bars, top & bottom)

pvc-towel-rack2



Instructions to make the DIY PVC pool towel rack!

  1. Once you have cut all your pieces start fitting the pipe pieces into the fittings.
  2. You will connect the foot elbows with the 37″ pipes (the legs) and then connect 2 of the legs to one 17.5″ pipe. At this point, you should have created two large side leg pieces.
  3. You will then connect the tees to the tops of the 37″ pieces and again connect the 17.5″ pipes to those. You will have created a rectangle and now you are ready to connect your elbows with slips.
  4. The slip side will go down into the tees and you will connect your towel bars to the other side.


To be honest, trying to read the directions of me explaining it is probably more confusing than just using the pictures above and just eyeing it. I’m pretty sure all of you can figure out what goes where.

Notes:

This PVC pipe is not furniture grade so you will have the ugly wording on the sidebars. It doesn’t bother me for now but if you want you can paint your towel bar.

I would strongly suggest roughing it up with sandpaper prior to painting so the paint will adhere better. I would also recommend a coat of primer to help cover up the markings.

You could also purchase furniture grade PVC, however, if the point is to keep cost at bay. Furniture grade PVC will be much more expensive.

While we are talking about enjoying the fun poolside this summer, I thought I would let you know about some of our favorite pool accessories.

Quick Dry Beach / Pool Towels
Diving Pool Toys Variety Pack
4 in 1 Pool Float

If you have a larger family and this towel rack won’t fit your needs I found another DIY video instruction for a bigger version.


If you enjoyed this PVC pool towel rack post you may also find these other pool projects a hit this summer.



13 comments

You may also like

Leave a Reply to Melissa Coleman Cancel Reply

13 comments

Julie Jordan Scott June 15, 2012 - 5:04 PM

Oh, this is fantastic!! What a simple (and useful DIY!) I can see it put to so many good uses even beyond hanging pool towels….

I hopped over here from Blog until you Drop… hope you will Visit My Blog, too!

Reply
A Proverbs 31 Wife June 15, 2012 - 5:34 PM

PVC is incredibly versatile! Who said it was only for plumbing? 🙂

Reply
♥ Shar June 15, 2012 - 7:42 PM

Very good idea! And much better than spending $200 on Etsy!

Have a great weekend Melissa!

xoxo -Shar

Reply
The Lacquer Factor June 16, 2012 - 3:27 AM

PVC is so versatile!! This is a great diy!!

Reply
Southern Glamourista June 17, 2012 - 5:38 PM Reply
Steph @ Crafting in the Rain June 18, 2012 - 5:59 PM

What a great idea!

Reply
Stevie from GardenTherapy.ca June 19, 2012 - 3:03 PM

this is such a great idea! I’m always looking for a spot for wet towels.

Reply
Emily June 22, 2012 - 3:14 PM

Great Idea. I might not get it done this summer but I’m pinning it for next summer.

Reply
CAPERNIUS July 4, 2014 - 2:43 PM

This is a COOL DIY project!!! My only complaint about it is, “why didn’t I think of that?” LOL
TY for sharing this. 🙂

To remove the words from the pipes forever, simple rubbing alcohol or plumbing pipe cleaner will do it. All you do is get it on a rag & wipe it off. period. no “elbow grease”, no fighting or struggling..just gently wipe it on & watch it disappear.
one 10 foot section of pipe can be cleaned in about 2 – 3 minutes. You don’t even have to wipe it down afterwards….once you wipe it down with the alcohol/pipe cleaner, it takes about 30 – 45 SECONDS to dry…you will feel no residue afterwards…ever.

I’ve plumbed many a house & barn, so I speak from experience.

Reply
Melissa Coleman July 7, 2014 - 8:06 PM

I never thought about using alcohol to take the words off the pvc pipe, great idea. Thanks!

Reply
Sandy January 10, 2017 - 4:32 PM

FYI – to get the words/lettering off the pipe, simply wipe it down with paint remover. Works great and removes all scuffs, wording and dirt!

Reply
Melissa Coleman January 11, 2017 - 10:58 AM

Awesome Sandy, thanks for the great tip. 🙂

Reply